Chinon Handyzoom 5001 This camera manual library is for reference and historical purposes, all rights reserved. This page is copyright by M. But
NOTE: The Battery should be replaced if either of the following conditions occurs: · The Battery check mark on the LCD panel blinks and the shutter
AUTOMATIC FILM SPEED SETTING The film speed is automatically set when using a DX coded film of ISO 25-1600 (Fig. 6). Non DX film will be set to ISO
(2) Insert a film cartridge into the film chamber (Fig 8). (3) Place the trimmed end of the film on the take-up spool up to the film tip mark. Make
NOTE: If "0" is blinking on the LCD panel, the film did not advance properly (Fig. 10). Open the Back Cover and reload the film. When placin
VIEWFINDER 1. Bright line frame 2. Multi AF frame 3. Central spot AF frame 4. Parallax marks 5. Exposure LED (red) 6. AF indicator LED (Two col
LCD DISPLAY PANEL 1. Auto Programmed Zoom Composing Mode 2. Self-timer Mode 3. Continuous Shooting Mode 4. Program AE Modes AUTO = Normal Progra
AUTO FOCUS SHOOTING The Chinon Handyzoom is equipped with a unique foolproof multi-spot auto focus system where the optimum focus distance is ach
NOTE: · The effective coverage angle of the multi autofocusing system varies with the lens focal length (Fig. 14), as per the illustration below. In
Focus Lock System This feature may be used when the main subject is located "off center" in the viewfinder. 1. Focus on the main subject
ZOOMING SYSTEM The Chinon Handyzoom is equipped with the world's first Auto Programmed Zoom Composing system that automatically selects an op
Holding the Camera ... ... 23 Viewfinder ... 25 LCD Display Panel ... 2
(3) Press the Shutter Release Button halfway and the Handyzoom will automatically set the zoom lens to the correct programmed focal length according t
(1) Slide the Main Switch to the "POWER" (Manual Power Zooming) position. The Auto Programmed Zoom Composing symbol mark will disappear from
(3) Push the Back Cover Release Button down to open the Back Cover and remove the cartridge from the film chamber. Be sure the frame counter shows &qu
NOTE: By pressing the Self-timer/Continuous Button ( ), three different picture taking modes can be selected: Normal Shooting Mode, Self-time
(1 ) When the Shutter Release Button is pressed halfway, the "AUTO" mark and the flash symbol mark ( ) will appear on the LCD panel. If th
Fill-in Flash Mode If the main subject has less light falling on it than on the surrounding area and background, under expo sure of the main subject
pictures to avoid camera shake. · To cancel the Fill-in Flash mode, press the Flash Mode Button twice to go back to the Normal Shooting mode (sens
(1) The Off-flash mode can be selected by pressing the Flash Mode Button twice. The "OFF" mark will appear on the LCD panel when it is set (
(3) Press the Shutter Release Button completely to take the picture. NOTE: · In this mode, the Slow Shutter Program AE will be automatical
(1 ) Select either the Off-flash or Fill-in Flash mode by pressing the Flash Mode Button (Fig. 35). (2) Press the Shutter Release Button halfway and
4. Lens4.butkus.o rg 5. Exposure metering window 6. Manual rewind botton 7. Flash mode button 8. BLC (Back Light Control) button 9. Spot AF butto
NOTE: · A tripod must be used for Bulb photography · In either of the above two Modes, the camera switches itself to the Bulb mode only at a brightn
(1 ) Press and hold the BLC button on top of the camera and release the shutter gently to take the photograph. Exposure of the main subject will be au
20. Back r over 21. Take up spool 22. Film guide 23. Film tip mark 24. Tripod socket SPECIFICATIONS TYPE: 35 mm fully automatic AF zoom co
SHUTTER: Stepping motor controlled chargeless shutter. Shutter speed: 1/4-1/300sec.+Buib. Release type: Electromagnetic type. EXPOSURE: Three mode
Strap: Attachable. Release lock: Built-in. Auto Shut Off: Built-in (Approx. 30 sec.). Power source: User replaceable 2CR5, 6 volt Lithium battery.4
5. DIRECT THE MULTI AF FRAME TO WARD YOUR SUBJECT (FIG. E). 6. RELEASE THE SHUTTER BY PRESSING THE SHUTTER RELEASE GENTLY (FIG. F). 7. AUTOMATIC FI
BATTERY INSTALLATION (1 ) Insert a pointed object such as a ball-point pen into the Battery Cover Release Hole on the bottom of the camera and open
Battery Check (1 ) Tum the Main Switch to the "AUTO" (Auto Programmed Zoom) position (Fig. 4). (2) The Battery check, frame counter an
Comments to this Manuals